PAPER INNER CYLINDERS
(These barber pole parts are preferred for restoration of old poles)

All Paper Inner Cylinders supplied with Metal Ends (spiders) attached except as noted.

3¼ X 10 - Marvy No. 410 - $41.95
3¼ X 16 - Marvy No. 405 & 607 - $41.95
3¼ X 18 - Marvy No.418 - $42.95
3¼ X 20 - Marvy No. 506 - $42.95
4 X 14½ - Paidar No. 928 Available only without Metal Ends - $48.95
5 X 16½ - Koch & Paidar Must re-use strap from old lower end - $57.95
5 X 17 - Koch & Paidar "B" motor only - $57.95
5¼ X 16 - Marvy No. 55, 66 & Koken - $57.95
6¾ X 19 - Koch & Paidar Fits Type "B" motor unless Type "A" requested - $69.95
6¾ X 20 - Marvy No. 88 & Koken - $69.95
6¾ X 22 - Koch & Paidar Fits Type "B" motor unless Type "A" requested - $69.95
6¾ X 24 - Marvy No. 824 & Koken - $69.95

TOP CYLINDER BUSHINGS

- 5¾" long (plastic & metal). This bridge, which is a combination of plastic and sheet metal, is used on Marvy No. 88, 824 & Koken poles which use an inner cylinder of 6¾" diameter. (This bushing is not used on Paidar or Koch poles.) - $9.95
STANDARD SIZE TOP CYLINDER BUSHING - 3½" long (plastic). Fits Paidar & Koch barber poles; also fits Marvy No. 55, 66, 77 & 99 poles - $8.95
SMALL SIZE TOP CYLINDER BUSHING - 3" long (plastic). Used on Marvy No. 405, 410, 418, 506 & 607 poles; will not fit Koken poles or Paidar & Koch poles - $8.95
ROUND TOP CYLINDER BUSHING - 2¾" diameter (plastic). Fits Koken poles only. This round top cylinder bushing is standard replacement for Koken barber poles which use a 6" diameter glass cylinder - $8.95
TOP CYLINDER SCREWS - (Two required). Used on all poles where the top bushing is 3½" or 3" - $.95

 

BARBER POLE MOTORS

TYPE "A" MOTOR
This motor has a 'cross-pin' on the output shaft and fits all Marvy Barber Poles. It also fits all Koken Barber Poles and some Paidar and Koch Poles. - $132.95

TYPE "B" MOTOR
This motor fits many Paidar & Koch Barber Poles. The Type "B" motor has a brass cup affixed to the top of the output shaft. - $132.95

 

MOTOR MOUNTING PLATES
Price for all motor mounting plates - $10.95

Type "A" fits Marvy poles with 6" or 8" diameter glass cylinders
Type "A-2" fits Marvy poles with 4" diameter glass cylinders
Type "C" fits most poles with 6" diameter glass cylinders, EXCEPT KOKEN
Type "D" fits most poles with 8" diameter glass cylinders, EXCEPT KOKEN

Barber Pole Motor Coil (Standard)
One style fits all barber poles - old style motors only - $31.95

Slotted Cup for Type "B" Motor - $14.95

42-Tooth Fiber Gear - old style motors only - $15.95

Three Way Switch - for all barber poles - $10.95

 

STAINLESS STEEL DOMES AND BOWLS FOR BARBER POLES

DOMES (tops)
Marvy No. 333, 405, 410, 418, 506 & 607 (Inside Diameter of 5¼") - $24.95
Marvy No. 44, 55, 66, 77 & 99 (Inside Diameter of 7¼") - $33.95
Marvy No. 88 & 824 (Inside Dia. 9½") - $42.95
Paidar & Koch No. 98, 198, 99, 199, 102 & 202 (Inside Diameter of 9½") - $44.95

BOWLS (bottoms)
Marvy No. 333, 405, 410, 418, 506 & 607 (Inside Diameter of 5¼") - $25.95
Marvy No. 44, 55, 66, 77 & 99 (Inside Diameter 7¼") - $34.95
Marvy No. 88 & 824 (Inside Diameter of 9½") - $42.95
Paidar & Koch No. 98, 198, 99, 199, 102 & 202 (Inside Diameter of 9½") - $44.95
(Screws furnished with Domes and Bowls)

 

REPLACEMENT LAMPS AND LIGHTING ACCESSORIES

INCANDESCENT BULBS
15A15 – 130 V, 15 watt, Appliance Size
FOR POLES WITH 4" DIAMETER GLASS - $5.95
25T10/F – 130 V, 25 watt tubular type lamp, 5¼" length,
(sometimes called a showcase lamp)
FOR POLES WITH 4" DIAMETER GLASS - $6.95
40T10/F – 130 V, 40 watt tubular type lamp, 5¼" length,
(sometimes called a showcase lamp)
FOR POLES WITH 6" DIAMETER GLASS - $6.95
75A/RS – 130 V, 75 watt Commercial Service lamp
FOR POLES WITH 8" DIAMETER GLASS - $6.95
Above lamps are special long-life lamps, good for approximately 2,500 hours

FLUORESCENT LAMPS
10W40F/TW – 130V, 10 watt, output of 40 watt, fluorescent, mini-twist
FOR POLES WITH 4" DIAMETER GLASS - $9.95
14W60F/TW– 130V, 14 watt, output of 60 watt, fluorescent, mini-twist
FOR POLES WITH 6" DIAMETER GLASS - $9.95
25W100F/TW – 130V, 25 watt, output of 100 watt, fluorescent, mini-twist
FOR POLES WITH 8" DIAMETER GLASS - $9.95
Above lamps are special long-life lamps, good for approximately 6,000-10,000 hours.
(In addition to longer life, these lamps save you money on your electric bill!)

FLUORESCENT LIGHT SLEEVES
Red, white & blue - for use over fluorescent light tube. The following sizes are available:
24" length - $32.95
18" length - $32.95

TWO-LIGHT CONVERSION KITS
These conversion kits will convert Marvy barber poles as indicated below from a standard one-light barber pole to a two-light model. All parts needed for conversion will be included. Please specify model number for best results.
Kit to convert Marvy models 333, 405, 410, 506 & 607 - $116.95
Kit to convert Marvy models 55, 66, 77 & 99 - $143.95
Kit to convert Marvy models 88 & 824 - $224.95

SPECIAL ORDER LIGHT FIXTURES (Less Light Bulbs)
One-Light Model - $36.95
Two-Light Model - $48.95
Specify brand and model number of barber pole that you need the light fixture for. These are made to order.

Replacement Porcelain Lamp Socket - $6.95

PLASTIC GLOBES(unbreakable)
8" with 4" opening fits Marvy 55,66 & 77 Two-Light & Koken - $39.95
10" with 4" opening fits Koch & Paidar - $47.95

GLASS GLOBES(Milk White - For top of "Two-Light" poles)
6" with 3" opening fits Marvy 333, 405, 410, 506 & 607 Two-Light - $24.95
8" with 4" opening fits Marvy 55, 66 & 77 Two-Light & Koken - $33.95
10" with 4" opening fits Koch & Paidar - $47.95
10" with 6" opening fits Marvy 88 & 824 Two-Light & Koken - $77.95

CANTEEN GLOBE
12" with 4" "Canteen Style" Glass Globe with decoration - $152.95

 

** FREE SHIPPING ** is included on all barber pole parts orders over $400.00!
Continental U.S. only.
We try to have the best prices on the web for barber pole parts. Call us today with your needs!